 |
|
|
| |
 |
FLOORGUARD SEALER is a Water-Based Floor Finish which is designed for mopping
over a range of floor coatings to provide a high gloss and
hard wearing surface. This general purpose product provides
a “sacrificial” protective film over floor coatings such
as Phoenix MAGNACOAT and Phoenix TUFFCOAT.
FLOORGUARD is based
upon a multiple High Performance Polymer Emulsion system
which offers impressive characteristics and
makes the product very easy to use to rejuvenate wearing
floor areas. Included in the formula is high performance
synthetic wax emulsion which provides an excellent resistance
to scuffing and offers a “black heel” mark resistance. The
product gives off no noxious, flammable, or carcinogenic
fumes, and only water is required for cleaning up.
| SPECIAL FEATURES: |
| |
- Good wear resistance
- Water Clean Up
- No expensive and highly dangerous solvents
- Forms a non-Toxic film
- Easy to brush or mop on
- Non-Flammable
|
|
- Superior resistance to dirt pick-up
- Gives off no fumes
- Safe for enclosed spaces
- Recoatability at any time
- Excellent adhesion promotion
- Fast development of hardness
|
|
This product has been designed for easy application
over most polished or clear coated floor surfaces, and offers
a particularly high gloss finish in conjunction with an excellent
resistance to wear. It can also be used directly onto clean
floors with a closed cell or non-porous surfaces, such as
vinyl and lino floors.
The product assists in extending the
life of the underlying floor surface by acting as a sacrificial
or wear coat, and
is easily applied over a clean floor surface using a SHURLINE
PAINTER PAD (Rota Cota) or similar product.
If the coating
shows signs of building up on the floor over a period of
time, the old FLOORGUARD may be removed using
an ammonia-rich floor cleanser, which will dissolve the old
coating away back down to the PHOENIX MAGNACOAT or TUFFCOAT
surface, which is chemically resistant to many chemicals,
including dilute ammonia solutions .
OTHER
PRODUCT ADVANTAGES:
The acrylic emulsions used
in the PHOENIX FLOORGUARD are completely up-to-date products
which embody no less than
three separate self-levelling additives to ensure the highest
possible finish is obtained.
For Commercial and Industrial
environments, FLOORGUARD may also be machine-buffed (using
a medium speed buffing machine)
for enhanced maintenance, but its main use is for the simple
“mop-on” procedure.
The coating is Water-Based and therefore
enables all mops etc. to be cleaned up easily. The product
gives off no offensive
smells of fumes while being applied and is suitable for use
in confined spaces.
| TYPICAL APPLICATIONS: |
| |
|
| FLOORGUARD on bar floor area. |
|
|
|
| FLOORGUARD on bar floor area. |
|
|
| FLOORGUARD on bar floor area. |
|
|
|
| FLOORGUARD on country supermarket floor. |
|
|
| PHYSICAL PROPERTIES: |
| |
| Appearance: |
White milky - looking emulsion, with characteristic
odour |
| Pot Life: |
Indefinite |
| Specific
Gravity: |
1.0 |
| Colour after
application: |
Clear when fully dried |
| Dilution: |
Must not be diluted |
| Clean up: |
Water |
| Recoating
Times: |
Approx 60 minutes or longer between coats (under
normal conditions, temperature above 25°C,
and low humidity). |
| Coverage: |
For most applications, 1 to 2 coats of the FLOORGUARD will suffice. Subsequent coats spread further,
but rates usually in range 15 to 20 square metres
per litre. The second coat is best applied on the
following day. |
| PRODUCT
INFORMATION SHEET: |
| |
|
For your convenience we have provided as a download, a PRODUCT
INFORMATION SHEET in Adobe Acrobat format below.
FLOORGUARD.pdf
To view a PDF file you must have Adobe Acrobat reader. It is free,
and is available below.
Adobe Acrobat (4mb)
|
|
|
|
| |
|
|
|
